BGXBG - S-1200 CONTACT ADHESIVE
- MSDS: BGXBG
- Manufacturer: ARMSTRONG WORLD INDUSTRIES INC FLOOR PRODUCTS DIV
- Product Name: S-1200 CONTACT ADHESIVE
- National Stock Number: 8040-01-035-7849
Product Identification
Product ID:S-1200 CONTACT ADHESIVE
MSDS Date:11/04/1985
FSC:8040
NIIN:01-035-7849
MSDS Number: BGXBG
Responsible Party
LANCASTER, PA 17604
US
Emergency Phone: 717-396-2348
Info Phone: 717-396-2729 OR 717-396-2935
Preparer: D.E. BOUDER
Cage: 03938
Contractor
Telephone: 717-396-2328; 717-396-2935
Cage: 03938
Ingredients
ACETONE (SARA III)
CAS: 67-64-1
RTECS: AL3150000
Fraction By Weight: 15%
OSHA PEL 1000PPM
ACGIH TLV: 750PPM/1000STEL;9293
EPA Report Quantity: 5000 LBS
DOT Report Quantity: 5000 LBS
METHYL ETHYL KETONE (2-BUTANONE) (MEK) (SARA III)
CAS: 78-93-3
RTECS: EL6475000
Fraction By Weight: 5%.
OSHA PEL 200 PPM/300 STEL
ACGIH TLV: 200 PPM/300STEL 9192
EPA Report Quantity: 5000 LBS
DOT Report Quantity: 5000 LBS
NAPHTA (PETROLEUM SPIRITS OR BENZIN)
CAS: 8030-30-6
RTECS: DE3030000
Fraction By Weight: 50%.
OSHA PEL 100 PPM
TOLUENE (SARA III)
CAS: 108-88-3
RTECS: XS5250000
Fraction By Weight: 5%.
OSHA PEL 200 PPM/150 STEL
ACGIH TLV: 50 PPM; 9293
EPA Report Quantity: 1000 LBS
DOT Report Quantity: 1000 LBS
SYNTHETIC RUBBER
Fraction By Weight: 15%.
OSHA PEL NONE ESTABLISHED
ACGIH TLV: NONE ESTABLISHED
PHENOLIC RESINS
Fraction By Weight: 5%.
OSHA PEL NONE ESTABLISHED
ACGIH TLV: NONE ESTABLISHED
RUBBER CURING INGREDIENTS
Fraction By Weight: 5%.
OSHA PEL NONE ESTABLISHED
ACGIH TLV: NONE ESTABLISHED
Hazards
LD50 LC50 Mixture:MFR PROVIDES NO INFORMATION
Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: RESPIRATORY & SKIN IRRITANT;
CNS' EFFECTS OR DEPRESSION FROM OVEREXPOSURE; CHRONIC: N/K .
Effects of Overexposure:INHAL:RESPIRATORY TRACT IRRITATION, COUGHING,
HEADACHE, DIZZINESS, DROWSINESS, NAUSEA, UNCOORDINATED MOVEMENTS;
SKIN/EYES: EXCESSIVE SKIN CONTAT MAY CAUSE DRYING & CRACKING &
RESULT IN DERMATITIS. CON TACT W/ EYES WILL CAUSE IRRITATION &
TISSUE DEFATTING.
Medical Cond Aggravated by Exposure:PREEXISTING RESPIRATORY AND/OR
DERMAL CONDITIONS (FPD).
First Aid
First Aid:INHAL: REMOVE TO FRESH AIR IF EXPOSED TO EXCESS VAPOR
CONCENTRATIONS. SEEK MED ATTN. IF SYMPTOMS PERSIST; SKIN/EYES:
FLUSH ANY SKIN OR EYE CONTACT W/ PLENTY OF WATER. ADDITIONALLY W/
SKIN CONTACT, WAS H W/ SOAP & WATER. REFER TO PHYSICIAN
IFIRRITATION OR SYMPTOMS PERSIST.
Fire Fighting
Flash Point:<20F/<-6.67C
Extinguishing Media:CARBON DIOXIDE,DRY CHEMICAL,HALON.
Fire Fighting Procedures:PROTECT FIRE FIGHTERS FROM TOXIC PRODUCTS OF
COMBUSTION BY WEARING SELF-CONTAINED BREATHING APPARATUS.
Unusual Fire/Explosion Hazard:CLOSED CONTAINERS IN A FIRE MAY RUPTURE
DUE TO PRESSURE BUILD-UP; USE WATER TO COOL CONTAINERS TO PREVENT
THIS.
Accidental Release
Spill Release Procedures:REMOVE ALL IGNITION SOURCES. VENTILATE AREA OF
SPILL OR LEAK. IF USING MECHANICAL VENTILATION, MAKE SURE IT IS
EXPLOSION PROOF OR DOES NOT PRESENT AN IGNITION SOURCE. WEAR APPRVD
RESPIRATORY EQUIPM. F OR EXPOSURES ABOVE PEL/TLV. USE INERT
ABSORBENT!
Handling
Handling and Storage Precautions:STORE IN AREA SUITABLE FOR FLAMMABLE
MIXTURES. RECOMMENDED STORAGE TEMPERATURES IS BELOW 90F/32.2C.
Other Precautions:VAPORS ARE FLAMMABLE & HEAVIER THAN AIR. PROHIBIT
SMOKING & ELIMINATE ALL IGNITION SOURCES, SUCH AS REGULAR
ELECTRICAL TOOLS & APPLICANCES,MAKING SURE THAT PILOTS ON GAS-FIRED
WATER HEATERS ARE EXTING UISHED.
Exposure Controls
Respiratory Protection:W/ADEQUATE VENTILATION, RESPIRATORY EQUIPMENT
SHOULD NOT BE NEEDED. IF ADEQUATE VENTILATION IS NOT AFFORDED, WEAR
RESPIRATORY EQUIPMENT APPROVED FOR ORGANIC VAPORS.
Ventilation:NATURAL CROSS-VENTILATION, LOCAL(MECHANICAL),PICK-UP AND/OR
GENERAL AREA(MECHANICAL)VENTILATION TO PREVENT BUILD-UP.
Protective Gloves:COTTON OR LOOP-PILE GLOVES FOR END-USE.
Eye Protection:SAFETY GLASSES.
Other Protective Equipment:AS REQUIRED FOR TASK AT HAND TO MINIMIZE
EXPOSURE OR PROVIDE FIRST AID IN THE EVENT OF OVEREXPOSURE.
Work Hygienic Practices:THIS CONTACT ADHESIVE IS FOR PROFESSIONAL OR
INDUSTRIAL USE ONLY! USE I/A/W SAFETY AND IH PROCEDURES SET FORTH.
Supplemental Safety and Health
Chemical Properties
HCC:F2
Vapor Density:>1.
Spec Gravity:0.82
Solubility in Water:NEGLIGIBLE
Appearance and Odor:STRAW COLORED LIQUID W/ CHARACTERISTIC SOLVENT
ODOR.
Percent Volatiles by Volume:>55
Stability
Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:MFR CITES NONE; IGNITION SOURCES & HIGH
TEMPERATURES .
Hazardous Decomposition Products:CARBON MONOXIDE, CARBON DIOXIDE, &
OTHER TOXIC VAPORS & GASES THAT ARE COMMON TO THERMAL DEGRADATION
OF ORGANIC COMPOUND
Disposal
Waste Disposal Methods:USE ABSORBENT TO ASSIST W/MATERIAL PICK-UP.
INCINERATION OR OTHER METHOD APPROVED FOR IGNITIBLE WASTES I/A/W
FEDERAL,STATE & LOCAL REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.